Amana ALG643RAW Instrukcja Właściciela Pobierz pdf

CONNECT

DRYER TO

EXHAUST

SYSTEM

Secure all joints with clamps or duct

tape. DO NOT use sheet metal

screws or other fastening means

which extend into the duct to attach

exhaust pipe joints. They could

catch lint and reduce the efficiency

of the exhaust system.

IMPORTANT: Keep exhaust duct

as short as possible.

Be sure old ducts are clean before

installing your new dryer.

To prevent backdraft when dryer is

not in operation, outer end of

exhaust pipe must have a weather

hood with hinged dampers (obtain

locally).

Weather hood should be installed

at least 12" (30.5 cm) above the

ground. Higher clearances may be

necessary in areas where heavy

snowfall can occur.

No extra system length

consideration is necessary when

exhausting through the roof. Use

MAXIMUM EXHAUST LENGTH

table to calculate system length.

Use a roof cap that provides air

flow equal to weather hood.

Exhaust Directions

Dryer can be exhausted to the

outdoors through the back, right, or

bottom of the dryer. Gas dryers

cannot be vented out the left

side because of the burner

housing.

Dryer is shipped from factory ready

for rear exhaust. No kits required.

To exhaust dryer through sides or

bottom, install a DK1 Sales

Accessory (Directional Exhaust Kit

528P3). Available as optional

equipment at extra cost.

CONNECT GAS

SUPPLY

Installation

Instructions

Gas Dryer

Keep instructions for future

reference. Be sure manual

stays with dryer.

Exhaust System Materials

Exhaust duct must be four inches

(10.2 cm) in diameter without

obstructions. Rigid metal duct is

recommended. Non-combustible

semirigid flexible metal duct is

acceptable.

DO NOT use plastic pipe, foil pipe,

or flexible plastic pipe, because it

contributes to poor drying

performance and collects lint, which

can lead to a fire hazard. To identify

flexible foil or plastic duct, pinch the

coils of the duct between your

fingers. If the coils can be brought

together, do not use the duct.

Do Not Use

Use

Rigid Metal Semirigid Metal

Flexible Foil Plastic

4" (10.16 cm)

Recommended Weather Hood

2-1/2" (6.35 cm)

Recommended

for Short Runs Only

POSITION AND

LEVEL DRYER

Place dryer in position, adjust all

legs (4) until dryer is level side to

side and front to back.

REMOVE PARTS

AND CLEAN

DRYER DRUM

Wipe drum with clean rag and soap

diluted in warm water to remove any

oil used in manufacturing. Make a

paste of laundry detergent and clean

drum if necessary.

Questions?

See Owners Manual or

call Amana Consumer Affairs

Department 1-800-843-0304

Optional Kits

Kits are available at extra cost through

your Amana dealer or

Amana factory 1-800-843-0304.

Directional Exhaust Kit

DK1 Sales Accessory (Directional

Exhaust Kit #528P3).

Flexible Metal Vent Kit

Exhausting the dryer in hard-to-reach

locations can be accomplished by

installing Kit # 521P3.

Manufactured (Mobile) Home

Installation Kit

Manufactured home anchor Kit

#526P3.

Propane Gas Conversion Kit

LPK1 Sales Accessory (L.P./Propane

Kit # 649P3).

Test for Gas

Leaks

After final gas

connection is made,

turn on manual gas

valve and test all connections in gas

supply piping for gas leaks. Leak

testing of the appliance shall be

conducted according to the

manufacturer’s instructions.

1. Place soap suds on connections.

2. If bubbles appear, a leak is

present. Shut off gas supply

valve.

3. Tighten joint if leak is at factory

fitting.

• If leak is not at factory fitting,

unscrew, apply more joint

compound, and tighten to

correct leak.

4. Retest connection for leak after

tightening or adding joint

compound.

• Retest any connections that

were disturbed.

Altitude

Ft (M)

Orifice

Size #

Part

number

3000 (915) 43 503778

6000 (1830) 44 58719

8000 (2440) 45 503779

9000 (2740) 46 503780

10000(3050) 47 503781

For proper operation at

altitudes above 2,500 feet

The natural gas valve spud orifice

size must be reduced to ensure

complete combustion. See table.

Connect gas supply to dryer using a new stainless steel flexible connector

or hard pipe (check local codes) according to illustration. Test for leaks and

check burner flame after gas supply is connected. See

Checking Burner

Flame

section on next page.

• Dryer must be connected to type of gas as shown on nameplate located

in the door recess.

• Use pipe joint compound insoluble on LP (propane) Gas, or Teflon tape,

on all pipe threads.

• Purge air and sediment from gas supply line before connecting it to the

dryer. Before tightening the connection, purge remaining air from gas line

to dryer until odor of gas is detected. This step is required to prevent gas

valve contamination.

CONNECT

POWER CORD

ELECTRICITY

See

Installation Requirements

section. Plug dryer into

3-prong grounded outlet only.

You'll Need a Few Things Before You Begin

L.P./Propane

DO NOT connect dryer to L.P./

Propane gas service without

converting the gas valve. An LPK1

Sales Accessory L.P./Propane Gas

Conversion Kit 649P3 must be

installed.

Duct Tape

Wrench

Screw

Drivers

Level

Teflon Tape or

Joint Compound

Stainless Steel

or Hard Pipe

Gas Connector

To reverse the direction that the

door opens, see the Owner’s

Manual.

Maximum Exhaust Length

Rigid Metal Duct

Number of

90º Elbows

Weather Hood

4-inch Opening

Weather Hood

2½-inch Opening

0 44 feet (13.4 m) 34 feet (10.4 m)

1 34 feet (10.4 m) 26 feet (7.9 m)

2 26 feet (7.9 m) 20 feet (6.1 m)

3 20 feet (6.1 m) 14 feet (4.3 m)

Flexible Metal Duct

Number of

90º Elbows

Weather Hood

4-inch Opening

Weather Hood

2½-inch Opening

0 24 feet (7.3 m) 20 feet (6.1 m)

1 20 feet (6.1 m) 16 feet (4.9 m)

2 16 feet (4.9 m) 12 feet (3.7 m)

3 12 feet (3.7 m) 8 feet (2.4 m)

NOTE: Deduct 6 feet (1.8 m) for each additional elbow.

Level

Dryer

Base

Leveling

Leg

" NPT gas

connection

Black iron pipe

Shorter than 20' (6.1 m) - use

" pipe

Longer than 20' (6.1 m) - use

" pipe

Use new stainless steel flexible connector

only if allowed by local codes (Use Design A.G.A. certified connector)

" NPT pipe plug

(for checking inlet

gas pressure)

Install Equipment

shut-off valve

within 6' (1.8 m)

of dryer.

1 2

Podsumowanie treści

Strona 1 - Instructions

CONNECTDRYER TOEXHAUSTSYSTEMSecure all joints with clamps or ducttape. DO NOT use sheet metalscrews or other fastening meanswhich extend into the duct

Strona 2 - Installation Requirements

Important Safety InformationSave These InstructionsGrounding InstructionsDryer must be grounded. Dryer is equipped with a cord having a groundingcondu

Komentarze do niniejszej Instrukcji

Brak uwag

Amana ALG643RAW Instrukcja Właściciela

Przeglądaj online lub pobierz Instrukcja Właściciela dla Elektryczne suszarki do prania Amana ALG643RAW. Amana ALG643RAW Owner`s manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Elektryczne suszarki do prania Amana ALG643RAW